DIY-LCD显示模块--JLT35002A

TLLED · 发表于 2025-5-10 17:34:06

趁着参加模块设计的几乎，把手上闲置的3.5寸显示型号JLT35002A设计个模块。

一、显示屏硬件

1.1、显示屏资料

显示屏驱动芯片型号是ILI9488
显示屏资料：

JLT35002A-PSS.pdf (2.04 MB, 下载次数: 3)

2025-5-10 17:12 上传

点击文件名下载附件
芯片资料：

ILI9488.PDF (10.35 MB, 下载次数: 1)

2025-5-10 17:13 上传

点击文件名下载附件

1.2、模块电路图

二、程序部分

在官方的例程上增加LCD驱动部分程序

2.1、lcd_ili9488.c

#include "main.h"
#include "lcd/lcd_ili9488.h"
#define ILI9488_ERROR_CHECK(x) \
do \
{ \
status_t ret = (x); \
if (ret != kStatus_Success) \
{ \
return ret; \
} \
} while (false)
#define ILI9488_CMD_SWRESET (0x01U)
#define ILI9488_CMD_SLPIN (0x10U)
#define ILI9488_CMD_SLPOUT (0x11U)
#define ILI9488_CMD_INVOFF (0x20U)
#define ILI9488_CMD_INVON (0x21U)
#define ILI9488_CMD_DISPOFF (0x28U)
#define ILI9488_CMD_DISPON (0x29U)
#define ILI9488_CMD_CASET (0x2AU)
#define ILI9488_CMD_RASET (0x2BU)
#define ILI9488_CMD_RAMWR (0x2CU)
#define ILI9488_CMD_TEOFF (0x34U)
#define ILI9488_CMD_TEON (0x35U)
#define ILI9488_CMD_MADCTL (0x36U) //--
#define ILI9488_CMD_COLMOD (0x3AU) //--
#define ILI9488_CMD_CSCON (0xF0U)
#define ILI9488_CMD_INVTR (0xB4U) //--
#define ILI9488_CMD_FRMCTR1 (0xB1U) //--
#define ILI9488_CMD_BPC (0xB5U)
#define ILI9488_CMD_DFC (0xB6U) //--
#define ILI9488_CMD_PWR1 (0xC0U) //--
#define ILI9488_CMD_PWR2 (0xC1U) //--
#define ILI9488_CMD_PWR3 (0xC2U)
#define ILI9488_CMD_VCMPCTL (0xC5U) //--
#define ILI9488_CMD_DOCA (0xE8U)
#define ILI9488_CMD_PGC (0xE0U) //--
#define ILI9488_CMD_NGC (0xE1U) //--
#define ILI9488_CMD_IMCTR 0xB0 //--
#define ILI9488_CMD_EMS 0xB7 //--
#define ILI9488_CMD_HSLS 0xBE //--
#define ILI9488_CMD_IMGFUNCT 0xE9 //--
#define ILI9488_CMD_ADJCTR3 0xF7
static const uint8_t s_ili9488_driver_preset_pars035[] = {
0x0F, ILI9488_CMD_PGC, 0x00, 0x07, 0x10, 0x09, 0x17, 0x0B, 0x40, 0x8A, 0x4B, 0x0A, 0x0D, 0x0F, 0x15, 0x16, 0x0F, // PGC--
0x0F, ILI9488_CMD_NGC, 0x00, 0x1A, 0x1B, 0x02, 0x0D, 0x05, 0x30, 0x35, 0x43, 0x02, 0x0A, 0x09, 0x32, 0x36, 0x0F, // NGC--
0x02, ILI9488_CMD_PWR1, 0x17, 0x15,
0x01, ILI9488_CMD_PWR2, 0x41,
0x03, ILI9488_CMD_VCMPCTL, 0x00,0x30,0x80,
0x01, ILI9488_CMD_MADCTL, 0x48,
0x01, ILI9488_CMD_COLMOD, 0x55,
0x01, ILI9488_CMD_IMGFUNCT, 0x00,
0X04, ILI9488_CMD_ADJCTR3, 0xA9,0x51,0x2C,0x82,
0x01, ILI9488_CMD_FRMCTR1, 0xA0,
0x01, ILI9488_CMD_INVTR, 0x02,
0x02, ILI9488_CMD_DFC, 0x02,0x22,
0x01, ILI9488_CMD_EMS, 0xC6,
0x02, ILI9488_CMD_HSLS, 0x00,0x04,
};
static status_t ILI9488_WriteCommand(ili9488_handle_t *handle,
uint8_t command,
const uint8_t *params,
uint8_t param_len)
{
#if MCUX_DBI_LEGACY
ILI9488_ERROR_CHECK(handle->xferOps->writeCommand(handle->xferOpsData, command));
for (uint8_t i = 0; i < param_len; i++)
{
uint16_t param_data = params[i];
ILI9488_ERROR_CHECK(handle->xferOps->writeData(handle->xferOpsData, ¶m_data, 2U));
}
return kStatus_Success;
#else
return DBI_IFACE_WriteCmdData(handle->dbiIface, command, params, param_len);
#endif
}
static status_t ILI9488_PresetDriver(ili9488_handle_t *handle, ili9488_driver_preset_t preset)
{
const uint8_t *preset_ptr;
uint16_t preset_len;
if (kILI9488_DriverPresetLCDJLT35 == preset)
{
preset_ptr = s_ili9488_driver_preset_pars035;
preset_len = ARRAY_SIZE(s_ili9488_driver_preset_pars035);
}
else
{
return kStatus_InvalidArgument;
}
uint16_t i = 0;
while (i < preset_len)
{
uint8_t param_len = preset_ptr[i];
ILI9488_ERROR_CHECK(ILI9488_WriteCommand(handle, preset_ptr[i + 1u], &preset_ptr[i + 2u], param_len));
i += ((uint16_t)param_len + 2u); /* Next = parameter length + command byte + length itself */
}
return kStatus_Success;
}
static status_t ILI9488_SoftwareReset(ili9488_handle_t *handle)
{
ILI9488_ERROR_CHECK(ILI9488_WriteCommand(handle, ILI9488_CMD_SWRESET, NULL, 0));
SDK_DelayAtLeastUs(5 * 1000, SDK_DEVICE_MAXIMUM_CPU_CLOCK_FREQUENCY);
return kStatus_Success;
}
static status_t ILI9488_SleepMode(ili9488_handle_t *handle, bool sleep)
{
uint8_t slp_cmd;
if (sleep)
{
slp_cmd = ILI9488_CMD_SLPIN;
}
else
{
slp_cmd = ILI9488_CMD_SLPOUT;
}
return ILI9488_WriteCommand(handle, slp_cmd, NULL, 0);
}
#if MCUX_DBI_LEGACY
status_t ILI9488_Init(ili9488_handle_t *handle,
const ili9488_config_t *config,
const dbi_xfer_ops_t *xferOps,
void *xferOpsData)
#else
status_t ILI9488_Init(ili9488_handle_t *handle, const ili9488_config_t *config, dbi_iface_t *dbiIface)
#endif
{
#if MCUX_DBI_LEGACY
handle->xferOps = xferOps;
handle->xferOpsData = xferOpsData;
#else
handle->dbiIface = dbiIface;
#endif
ILI9488_ERROR_CHECK(ILI9488_SoftwareReset(handle));
ILI9488_ERROR_CHECK(ILI9488_PresetDriver(handle, config->driverPreset));
ILI9488_ERROR_CHECK(ILI9488_SleepMode(handle, false));
ILI9488_ERROR_CHECK(ILI9488_Config(handle, config));
return kStatus_Success;
}
status_t ILI9488_InvertDisplay(ili9488_handle_t *handle, bool invert)
{
uint8_t inv_cmd;
if (invert)
{
inv_cmd = ILI9488_CMD_INVON;
}
else
{
inv_cmd = ILI9488_CMD_INVOFF;
}
ILI9488_ERROR_CHECK(ILI9488_WriteCommand(handle, inv_cmd, NULL, 0U));
return kStatus_Success;
}
status_t ILI9488_EnableDisplay(ili9488_handle_t *handle, bool enable)
{
uint8_t disp_cmd;
if (enable)
{
disp_cmd = ILI9488_CMD_DISPON;
}
else
{
disp_cmd = ILI9488_CMD_DISPOFF;
}
ILI9488_ERROR_CHECK(ILI9488_WriteCommand(handle, disp_cmd, NULL, 0U));
return kStatus_Success;
}
status_t ILI9488_SetPixelFormat(ili9488_handle_t *handle, ili9488_pixel_format_t pixelFormat)
{
uint8_t pixel_fmt = (uint8_t)pixelFormat;
ILI9488_ERROR_CHECK(ILI9488_WriteCommand(handle, ILI9488_CMD_COLMOD, &pixel_fmt, 0x01U));
return kStatus_Success;
}
status_t ILI9488_SetTEConfig(ili9488_handle_t *handle, ili9488_te_config_t teConfig)
{
if (teConfig == kILI9488_TEDisabled)
{
ILI9488_ERROR_CHECK(ILI9488_WriteCommand(handle, ILI9488_CMD_TEOFF, NULL, 0U));
}
else
{
uint8_t te_cfg = 0x00U;
if (teConfig == kILI9488_TEHVSync)
{
te_cfg |= 0x01U; /* Set TEM bit */
}
ILI9488_ERROR_CHECK(ILI9488_WriteCommand(handle, ILI9488_CMD_TEON, &te_cfg, 1U));
}
return kStatus_Success;
}
status_t ILI9488_SelectArea(ili9488_handle_t *handle, uint16_t startX, uint16_t startY, uint16_t endX, uint16_t endY)
{
uint8_t tx_buf[4];
tx_buf[0] = (uint8_t)(startX >> 0x08U) & 0xFFU;
tx_buf[1] = (uint8_t)startX & 0xFFU;
tx_buf[2] = (uint8_t)(endX >> 0x08U) & 0xFFU;
tx_buf[3] = (uint8_t)endX & 0xFFU;
ILI9488_ERROR_CHECK(ILI9488_WriteCommand(handle, ILI9488_CMD_CASET, tx_buf, 4U));
tx_buf[0] = (uint8_t)(startY >> 0x08U) & 0xFFU;
tx_buf[1] = (uint8_t)startY & 0xFFU;
tx_buf[2] = (uint8_t)(endY >> 0x08U) & 0xFFU;
tx_buf[3] = (uint8_t)endY & 0xFFU;
ILI9488_ERROR_CHECK(ILI9488_WriteCommand(handle, ILI9488_CMD_RASET, tx_buf, 4U));
return kStatus_Success;
}
status_t ILI9488_Config(ili9488_handle_t *handle, const ili9488_config_t *config)
{
ILI9488_ERROR_CHECK(ILI9488_InvertDisplay(handle, config->invertDisplay));
ILI9488_ERROR_CHECK(ILI9488_SetPixelFormat(handle, config->pixelFormat));
ILI9488_ERROR_CHECK(ILI9488_SetTEConfig(handle, config->teConfig));
uint8_t tx_buf[1];
tx_buf[0] = (uint8_t)config->orientationMode;
if (!config->bgrFilter)
{
tx_buf[0] &= (uint8_t)(~0x08U);
}
if (config->flipDisplay)
{
if ((config->orientationMode == kILI9488_Orientation90) || (config->orientationMode == kILI9488_Orientation270))
{
tx_buf[0] ^= 0x80U;
}
else
{
tx_buf[0] ^= 0x40U;
}
}
ILI9488_ERROR_CHECK(ILI9488_WriteCommand(handle, ILI9488_CMD_MADCTL, tx_buf, 1U));
handle->orientationMode = config->orientationMode;
return kStatus_Success;
}
status_t ILI9488_WritePixels(ili9488_handle_t *handle, uint16_t *pixels, uint32_t len)
{
#if MCUX_DBI_LEGACY
ILI9488_ERROR_CHECK(handle->xferOps->writeMemory(handle->xferOpsData, ILI9488_CMD_RAMWR, pixels, len * 2u));
#else
ILI9488_ERROR_CHECK(DBI_IFACE_WriteMemory(handle->dbiIface, (const uint8_t *)pixels, len * 2u));
#endif
return kStatus_Success;
}
#if MCUX_DBI_LEGACY
void ILI9488_SetMemoryDoneCallback(ili9488_handle_t *handle, dbi_mem_done_callback_t callback, void *userData)
{
handle->xferOps->setMemoryDoneCallback(handle->xferOpsData, callback, userData);
}
#endif

复制代码

2.2、lcd_ili9488.h

#ifndef __LCD_ILI9488_H__
#define __LCD_ILI9488_H__
#include <stdbool.h>
#include "fsl_dbi.h"
typedef enum _ili9488_driver_preset
{
kILI9488_DriverPresetLCDJLT35,
} ili9488_driver_preset_t;
/*! @brief Display Orientation. */
typedef enum _ili9488_orientation_mode
{
kILI9488_Orientation0 = 0x08U, /*!< Rotation 0 degrees */
kILI9488_Orientation90 = 0x68U, /*!< Rotation 90 degrees */
kILI9488_Orientation180 = 0xC8U, /*!< Rotation 180 degrees */
kILI9488_Orientation270 = 0xA8U, /*!< Rotation 270 degrees */
} ili9488_orientation_mode_t;
/*! @brief Pixel format, does not affect interface width */
typedef enum _ili9488_pixel_format
{
kILI9488_PixelFormatRGB565 = 5U, /*!< Pixel format RGB565, 16bits per pixel */
kILI9488_PixelFormatRGB666 = 6U, /*!< Pixel format RGB666, 18bits per pixel */
kILI9488_PixelFormatRGB888 = 7U, /*!< Pixel format RGB888, 24bits per pixel, internally dithered to 18bits */
kILI9488_PixelFormatRGB444 = 3U, /*!< Pixel format RGB444, 12bits per pixel */
} ili9488_pixel_format_t;
/*! @brief TE (tearing effect) output configuration */
typedef enum _ili9488_te_config
{
kILI9488_TEDisabled, /*!< TE output disabled (no output) */
kILI9488_TEVSync, /*!< TE output enabled on VSync */
kILI9488_TEHVSync, /*!< TE output enabled on both HSync and VSync */
} ili9488_te_config_t;
/*! @brief Panel configuration structure */
typedef struct _ili9488_config
{
ili9488_driver_preset_t driverPreset; /*!< Driver configuration preset */
ili9488_pixel_format_t pixelFormat; /*!< Color format */
ili9488_orientation_mode_t orientationMode; /*!< Display orientation */
ili9488_te_config_t teConfig; /*!< TE line configuration */
bool invertDisplay; /*!< Invert display color */
bool flipDisplay; /*!< Mirror display image */
bool bgrFilter; /*!< Use BGR color filter instead of RGB */
} ili9488_config_t;
/*! @brief ili9488 driver handle structure */
typedef struct _ili9488_handle
{
#if MCUX_DBI_LEGACY
const dbi_xfer_ops_t *xferOps; /*!< Bus transfer operations. */
void *xferOpsData; /*!< Data used for transfer operations. */
#else
dbi_iface_t *dbiIface; /*!< DBI interface handle. */
#endif
ili9488_orientation_mode_t orientationMode; /*!< Current orientation mode */
} ili9488_handle_t;
/*******************************************************************************
* API
******************************************************************************/
#if defined(__cplusplus)
extern "C" {
#endif
#if MCUX_DBI_LEGACY
status_t ILI9488_Init(ili9488_handle_t *handle,
const ili9488_config_t *config,
const dbi_xfer_ops_t *xferOps,
void *xferOpsData);
#else
status_t ILI9488_Init(ili9488_handle_t *handle, const ili9488_config_t *config, dbi_iface_t *dbiIface);
#endif
status_t ILI9488_InvertDisplay(ili9488_handle_t *handle, bool invert);
status_t ILI9488_EnableDisplay(ili9488_handle_t *handle, bool enable);
status_t ILI9488_SetPixelFormat(ili9488_handle_t *handle, ili9488_pixel_format_t pixelFormat);
status_t ILI9488_SetTEConfig(ili9488_handle_t *handle, ili9488_te_config_t teConfig);
status_t ILI9488_Config(ili9488_handle_t *handle, const ili9488_config_t *config);
status_t ILI9488_SelectArea(ili9488_handle_t *handle, uint16_t startX, uint16_t startY, uint16_t endX, uint16_t endY);
status_t ILI9488_WritePixels(ili9488_handle_t *handle, uint16_t *pixels, uint32_t len);
#if MCUX_DBI_LEGACY
void ILI9488_SetMemoryDoneCallback(ili9488_handle_t *handle, dbi_mem_done_callback_t callback, void *userData);
#endif
#if defined(__cplusplus)
}
#endif
/*! @} */
#endif

复制代码

2.3、lvgl_support.c

/*
*
* SPDX-License-Identifier: BSD-3-Clause
*/
#include "lvgl_support.h"
#include "lvgl.h"
#if defined(SDK_OS_FREE_RTOS)
#include "FreeRTOS.h"
#include "semphr.h"
#endif
#include "board.h"
#include "fsl_gpio.h"
#if BOARD_USE_FLEXIO_SMARTDMA
#include "fsl_dbi_flexio_smartdma.h"
#else
#include "fsl_dbi_flexio_edma.h"
#endif
#include "fsl_flexio_mculcd.h"
#include "fsl_lpi2c.h"
#include "fsl_port.h"
#if BOARD_LCD_S035
#include "fsl_st7796s.h"
#include "fsl_gt911.h"
#elif BOARD_LCD_JLT35
#include "lcd/lcd_ili9488.h"
#include "fsl_gt911.h"
#else
#include "fsl_ssd1963.h"
#include "fsl_ft5406_rt.h"
#endif
#include "fsl_debug_console.h"
/*******************************************************************************
* Definitions
******************************************************************************/
/* Port Me. Start */
#if BOARD_LCD_S035
#elif BOARD_LCD_JLT35
#else
#define BOARD_SSD1963_XTAL_FREQ 10000000U
#define BOARD_SSD1963_PCLK_FREQ 25000000U//30000000U
#define BOARD_SSD1963_HSW 1U//48U
#define BOARD_SSD1963_HFP 116//40U
#define BOARD_SSD1963_HBP 44//0U
#define BOARD_SSD1963_VSW 1U//3U
#define BOARD_SSD1963_VFP 10U/13U
#define BOARD_SSD1963_VBP 34U//18U
#define BOARD_SSD1963_POLARITY_FLAG 0U
#endif
/* Macros for FlexIO interfacing the LCD */
#define BOARD_FLEXIO FLEXIO0
#define BOARD_FLEXIO_CLOCK_FREQ CLOCK_GetFlexioClkFreq()
#define BOARD_FLEXIO_BAUDRATE_BPS 160000000U
/* Macros for FlexIO shifter, timer, and pins. */
#define BOARD_FLEXIO_WR_PIN 1
#define BOARD_FLEXIO_RD_PIN 0
#define BOARD_FLEXIO_DATA_PIN_START 16
#define BOARD_FLEXIO_TX_START_SHIFTER 0
#define BOARD_FLEXIO_RX_START_SHIFTER 0
#define BOARD_FLEXIO_TX_END_SHIFTER 7
#define BOARD_FLEXIO_RX_END_SHIFTER 7
#define BOARD_FLEXIO_TIMER 0
/* Macros for the touch touch controller. */
#define BOARD_TOUCH_I2C LPI2C2
#define BOARD_TOUCH_I2C_CLOCK_FREQ CLOCK_GetLPFlexCommClkFreq(2u)
#define BOARD_TOUCH_I2C_BAUDRATE 100000U
/* Port Me. End */
#define DEMO_MS_TO_TICK(ms) ((ms * configTICK_RATE_HZ / 1000) + 1)
/*******************************************************************************
* Prototypes
******************************************************************************/
static void DEMO_InitLcd(void);
static void DEMO_InitLcdClock(void);
static status_t DEMO_InitLcdController(void);
static void DEMO_FlushDisplay(lv_disp_drv_t *disp_drv, const lv_area_t *area, lv_color_t *color_p);
static void DEMO_InitTouch(void);
static void DEMO_ReadTouch(lv_indev_drv_t *drv, lv_indev_data_t *data);
static void DEMO_SetCSPin(bool set);
static void DEMO_SetRSPin(bool set);
/*******************************************************************************
* Variables
******************************************************************************/
#if BOARD_LCD_S035
static gt911_handle_t touchHandle;
#elif BOARD_LCD_JLT35
static gt911_handle_t touchHandle;
#else
static ft5406_rt_handle_t touchHandle;
#endif
#if defined(SDK_OS_FREE_RTOS)
static SemaphoreHandle_t s_memWriteDone;
#else
static volatile bool s_memWriteDone;
#endif
#if BOARD_LCD_S035
/* ST7796S LCD controller handle. */
st7796s_handle_t lcdHandle;
#elif BOARD_LCD_JLT35
/* ST7796S LCD controller handle. */
ili9488_handle_t lcdHandle;
#else
/* SSD1963 LCD controller handle. */
ssd1963_handle_t lcdHandle;
#endif
/* DBI XFER handle. */
#if BOARD_USE_FLEXIO_SMARTDMA
dbi_flexio_smartdma_xfer_handle_t g_dbiFlexioXferHandle;
#else
dbi_flexio_edma_xfer_handle_t g_dbiFlexioXferHandle;
#endif
/* The FlexIO MCU LCD device. */
FLEXIO_MCULCD_Type flexioLcdDev = {
.flexioBase = BOARD_FLEXIO,
.busType = kFLEXIO_MCULCD_8080,
.dataPinStartIndex = BOARD_FLEXIO_DATA_PIN_START,
.ENWRPinIndex = BOARD_FLEXIO_WR_PIN,
.RDPinIndex = BOARD_FLEXIO_RD_PIN,
.txShifterStartIndex = BOARD_FLEXIO_TX_START_SHIFTER,
.txShifterEndIndex = BOARD_FLEXIO_TX_END_SHIFTER,
.rxShifterStartIndex = BOARD_FLEXIO_RX_START_SHIFTER,
.rxShifterEndIndex = BOARD_FLEXIO_RX_END_SHIFTER,
.timerIndex = BOARD_FLEXIO_TIMER,
.setCSPin = DEMO_SetCSPin,
.setRSPin = DEMO_SetRSPin,
.setRDWRPin = NULL /* Not used in 8080 mode. */
};
SDK_ALIGN(static uint8_t s_frameBuffer[2][LCD_VIRTUAL_BUF_SIZE * LCD_FB_BYTE_PER_PIXEL], 4);
/*******************************************************************************
* Code
******************************************************************************/
static void DEMO_SetCSPin(bool set)
{
GPIO_PinWrite(BOARD_LCD_CS_GPIO, BOARD_LCD_CS_PIN, (uint8_t)set);
}
static void DEMO_SetRSPin(bool set)
{
GPIO_PinWrite(BOARD_LCD_RS_GPIO, BOARD_LCD_RS_PIN, (uint8_t)set);
}
static void DEMO_DbiMemoryDoneCallback(status_t status, void *userData)
{
#if defined(SDK_OS_FREE_RTOS)
BaseType_t taskAwake = pdFALSE;
xSemaphoreGiveFromISR(s_memWriteDone, &taskAwake);
portYIELD_FROM_ISR(taskAwake);
#else
s_memWriteDone = true;
#endif
}
#if BOARD_LCD_S035
void DEMO_LCD_I2C_Init(void)
{
BOARD_LPI2C_Init(BOARD_TOUCH_I2C, BOARD_TOUCH_I2C_CLOCK_FREQ);
}
status_t DEMO_LCD_I2C_Send(
uint8_t deviceAddress, uint32_t subAddress, uint8_t subaddressSize, const uint8_t *txBuff, uint8_t txBuffSize)
{
return BOARD_LPI2C_Send(BOARD_TOUCH_I2C, deviceAddress, subAddress, subaddressSize, (uint8_t *)txBuff, txBuffSize);
}
status_t DEMO_LCD_I2C_Receive(
uint8_t deviceAddress, uint32_t subAddress, uint8_t subaddressSize, uint8_t *rxBuff, uint8_t rxBuffSize)
{
return BOARD_LPI2C_Receive(BOARD_TOUCH_I2C, deviceAddress, subAddress, subaddressSize, rxBuff, rxBuffSize);
}
void DEMO_TouchDelayMs(uint32_t delayMs)
{
#if defined(SDK_OS_FREE_RTOS)
vTaskDelay(pdMS_TO_TICKS(delayMs));
#else
SDK_DelayAtLeastUs(delayMs * 1000, CLOCK_GetCoreSysClkFreq());
#endif
}
void DEMO_TouchConfigIntPin(gt911_int_pin_mode_t mode)
{
port_pin_config_t int_config = {/* Internal pull-up/down resistor is disabled */
kPORT_PullDown,
/* Low internal pull resistor value is selected. */
kPORT_LowPullResistor,
/* Fast slew rate is configured */
kPORT_FastSlewRate,
/* Passive input filter is disabled */
kPORT_PassiveFilterDisable,
/* Open drain output is disabled */
kPORT_OpenDrainDisable,
/* Low drive strength is configured */
kPORT_LowDriveStrength,
/* Pin is configured as GPIO */
kPORT_MuxAlt0,
/* Digital input enabled */
kPORT_InputBufferEnable,
/* Digital input is not inverted */
kPORT_InputNormal,
/* Pin Control Register fields [15:0] are not locked */
kPORT_UnlockRegister};
switch (mode)
{
case kGT911_IntPinPullUp:
int_config.pullSelect = kPORT_PullUp;
break;
case kGT911_IntPinPullDown:
int_config.pullSelect = kPORT_PullDown;
break;
case kGT911_IntPinInput:
int_config.pullSelect = kPORT_PullDisable;
break;
default:
break;
};
PORT_SetPinConfig(BOARD_LCD_INT_PORT, BOARD_LCD_INT_PIN, &int_config);
}
void DEMO_TouchConfigResetPin(bool pullUp)
{
if(pullUp == true)
{
GPIO_PortSet(BOARD_LCD_TE_GPIO, 1u << BOARD_LCD_TE_PIN);
}
else
{
GPIO_PortClear(BOARD_LCD_TE_GPIO, 1u << BOARD_LCD_TE_PIN);
}
/*
* As touch controller and display controller shares the same reset pin,
* we do not do actual reset / address configuration here. Please check below for
* the relationship between RST pin and INT pin.
*
*/
}
#elif BOARD_LCD_JLT35
void DEMO_LCD_I2C_Init(void)
{
BOARD_LPI2C_Init(BOARD_TOUCH_I2C, BOARD_TOUCH_I2C_CLOCK_FREQ);
}
status_t DEMO_LCD_I2C_Send(
uint8_t deviceAddress, uint32_t subAddress, uint8_t subaddressSize, const uint8_t *txBuff, uint8_t txBuffSize)
{
return BOARD_LPI2C_Send(BOARD_TOUCH_I2C, deviceAddress, subAddress, subaddressSize, (uint8_t *)txBuff, txBuffSize);
}
status_t DEMO_LCD_I2C_Receive(
uint8_t deviceAddress, uint32_t subAddress, uint8_t subaddressSize, uint8_t *rxBuff, uint8_t rxBuffSize)
{
return BOARD_LPI2C_Receive(BOARD_TOUCH_I2C, deviceAddress, subAddress, subaddressSize, rxBuff, rxBuffSize);
}
void DEMO_TouchDelayMs(uint32_t delayMs)
{
#if defined(SDK_OS_FREE_RTOS)
vTaskDelay(pdMS_TO_TICKS(delayMs));
#else
SDK_DelayAtLeastUs(delayMs * 1000, CLOCK_GetCoreSysClkFreq());
#endif
}
void DEMO_TouchConfigIntPin(gt911_int_pin_mode_t mode)
{
port_pin_config_t int_config = {/* Internal pull-up/down resistor is disabled */
kPORT_PullDown,
/* Low internal pull resistor value is selected. */
kPORT_LowPullResistor,
/* Fast slew rate is configured */
kPORT_FastSlewRate,
/* Passive input filter is disabled */
kPORT_PassiveFilterDisable,
/* Open drain output is disabled */
kPORT_OpenDrainDisable,
/* Low drive strength is configured */
kPORT_LowDriveStrength,
/* Pin is configured as GPIO */
kPORT_MuxAlt0,
/* Digital input enabled */
kPORT_InputBufferEnable,
/* Digital input is not inverted */
kPORT_InputNormal,
/* Pin Control Register fields [15:0] are not locked */
kPORT_UnlockRegister};
switch (mode)
{
case kGT911_IntPinPullUp:
int_config.pullSelect = kPORT_PullUp;
break;
case kGT911_IntPinPullDown:
int_config.pullSelect = kPORT_PullDown;
break;
case kGT911_IntPinInput:
int_config.pullSelect = kPORT_PullDisable;
break;
default:
break;
};
PORT_SetPinConfig(BOARD_LCD_INT_PORT, BOARD_LCD_INT_PIN, &int_config);
}
void DEMO_TouchConfigResetPin(bool pullUp)
{
if(pullUp == true)
{
GPIO_PortSet(BOARD_LCD_TE_GPIO, 1u << BOARD_LCD_TE_PIN);
}
else
{
GPIO_PortClear(BOARD_LCD_TE_GPIO, 1u << BOARD_LCD_TE_PIN);
}
/*
* As touch controller and display controller shares the same reset pin,
* we do not do actual reset / address configuration here. Please check below for
* the relationship between RST pin and INT pin.
*
*/
}
#endif
/* Clear the LCD controller video memory content. */
static void DEMO_ClearLcd(void)
{
int32_t leftLinesToClear = LCD_HEIGHT;
int32_t curLinesToClear;
int32_t startLine = 0;
while (leftLinesToClear > 0)
{
curLinesToClear =
(leftLinesToClear > (2 * LCD_VIRTUAL_BUF_HEIGHT)) ? (2 * LCD_VIRTUAL_BUF_HEIGHT) : leftLinesToClear;
#if BOARD_LCD_S035
ST7796S_SelectArea(&lcdHandle, 0, startLine, LCD_WIDTH - 1, startLine + curLinesToClear - 1);
#elif BOARD_LCD_JLT35
ILI9488_SelectArea(&lcdHandle, 0, startLine, LCD_WIDTH - 1, startLine + curLinesToClear - 1);
#else
SSD1963_SelectArea(&lcdHandle, 0, startLine, LCD_WIDTH - 1, startLine + curLinesToClear - 1);
#endif
#if !defined(SDK_OS_FREE_RTOS)
s_memWriteDone = false;
#endif
#if BOARD_LCD_S035
ST7796S_WritePixels(&lcdHandle, (uint16_t *)s_frameBuffer, curLinesToClear * LCD_WIDTH);
#elif BOARD_LCD_JLT35
ILI9488_WritePixels(&lcdHandle, (uint16_t *)s_frameBuffer, curLinesToClear * LCD_WIDTH);
#else
SSD1963_WriteMemory(&lcdHandle, (const uint8_t *)s_frameBuffer,
curLinesToClear * LCD_WIDTH * LCD_FB_BYTE_PER_PIXEL);
#endif
#if defined(SDK_OS_FREE_RTOS)
if (xSemaphoreTake(s_memWriteDone, portMAX_DELAY) != pdTRUE)
{
PRINTF("Wait semaphore error: s_memWriteDone\r\n");
assert(0);
}
#else
while (false == s_memWriteDone)
{
}
#endif
startLine += curLinesToClear;
leftLinesToClear -= curLinesToClear;
}
}
status_t DEMO_InitLcdController(void)
{
status_t status;
flexio_mculcd_config_t flexioMcuLcdConfig;
#if BOARD_LCD_S035
const st7796s_config_t st7796sConfig = {.driverPreset = kST7796S_DriverPresetLCDPARS035,
.pixelFormat = kST7796S_PixelFormatRGB565,
.orientationMode = kST7796S_Orientation270,
.teConfig = kST7796S_TEDisabled,
.invertDisplay = true,
.flipDisplay = true,
.bgrFilter = true};
#elif BOARD_LCD_JLT35
const ili9488_config_t ili9488Config = {.driverPreset = kILI9488_DriverPresetLCDJLT35,
.pixelFormat = kILI9488_PixelFormatRGB565,
.orientationMode = kILI9488_Orientation90,
.teConfig = kILI9488_TEDisabled,
.invertDisplay = false,
.flipDisplay = false,
.bgrFilter = true};
#else
const ssd1963_config_t ssd1963Config = {.pclkFreq_Hz = BOARD_SSD1963_PCLK_FREQ,
.pixelInterface = kSSD1963_RGB565,
.panelDataWidth = kSSD1963_PanelData18Bit,
.polarityFlags = BOARD_SSD1963_POLARITY_FLAG,
.panelWidth = LCD_WIDTH,
.panelHeight = LCD_HEIGHT,
.hsw = BOARD_SSD1963_HSW,
.hfp = BOARD_SSD1963_HFP,
.hbp = BOARD_SSD1963_HBP,
.vsw = BOARD_SSD1963_VSW,
.vfp = BOARD_SSD1963_VFP,
.vbp = BOARD_SSD1963_VBP};
#endif
const gpio_pin_config_t pinConfig = {
.pinDirection = kGPIO_DigitalOutput,
.outputLogic = 1,
};
#if BOARD_USE_FLEXIO_SMARTDMA
flexio_mculcd_smartdma_config_t flexioEzhConfig = {
.inputPixelFormat = kFLEXIO_MCULCD_RGB565,
.outputPixelFormat = kFLEXIO_MCULCD_RGB565,
};
#endif
/* Set SSD1963 CS, RS, and reset pin to output. */
GPIO_PinInit(BOARD_LCD_RST_GPIO, BOARD_LCD_RST_PIN, &pinConfig);
GPIO_PinInit(BOARD_LCD_CS_GPIO, BOARD_LCD_CS_PIN, &pinConfig);
GPIO_PinInit(BOARD_LCD_RS_GPIO, BOARD_LCD_RS_PIN, &pinConfig);
/* Initialize the flexio MCU LCD. */
/*
* flexioMcuLcdConfig.enable = true;
* flexioMcuLcdConfig.enableInDoze = false;
* flexioMcuLcdConfig.enableInDebug = true;
* flexioMcuLcdConfig.enableFastAccess = true;
* flexioMcuLcdConfig.baudRate_Bps = 96000000U;
*/
FLEXIO_MCULCD_GetDefaultConfig(&flexioMcuLcdConfig);
flexioMcuLcdConfig.baudRate_Bps = BOARD_FLEXIO_BAUDRATE_BPS;
status = FLEXIO_MCULCD_Init(&flexioLcdDev, &flexioMcuLcdConfig, BOARD_FLEXIO_CLOCK_FREQ);
if (kStatus_Success != status)
{
return status;
}
#if BOARD_USE_FLEXIO_SMARTDMA
/* Create the DBI XFER handle. */
status = DBI_FLEXIO_SMARTDMA_CreateXferHandle(&g_dbiFlexioXferHandle, &flexioLcdDev, &flexioEzhConfig);
#else
/* Create the DBI XFER handle. Because DMA transfer is not used, so don't
* need to create DMA handle.
*/
status = DBI_FLEXIO_EDMA_CreateXferHandle(&g_dbiFlexioXferHandle, &flexioLcdDev, NULL, NULL);
#endif
if (kStatus_Success != status)
{
return status;
}
/* Reset the SSD1963 LCD controller. */
GPIO_PinWrite(BOARD_LCD_RST_GPIO, BOARD_LCD_RST_PIN, 0);
#if BOARD_LCD_S035
/* Required for GT911 I2C address mode 0 */
DEMO_TouchConfigIntPin(kGT911_IntPinPullDown);
#elif BOARD_LCD_JLT35
/* Required for GT911 I2C address mode 0 */
DEMO_TouchConfigIntPin(kGT911_IntPinPullDown);
#endif
#if defined(SDK_OS_FREE_RTOS)
vTaskDelay(DEMO_MS_TO_TICK(1)); /* Delay at least 10ns. */
#else
SDK_DelayAtLeastUs(1000U, SDK_DEVICE_MAXIMUM_CPU_CLOCK_FREQUENCY);
#endif
GPIO_PinWrite(BOARD_LCD_RST_GPIO, BOARD_LCD_RST_PIN, 1);
#if BOARD_LCD_S035
DEMO_TouchConfigIntPin(kGT911_IntPinInput);
#elif BOARD_LCD_JLT35
DEMO_TouchConfigIntPin(kGT911_IntPinInput);
#endif
#if defined(SDK_OS_FREE_RTOS)
vTaskDelay(DEMO_MS_TO_TICK(5)); /* Delay at 5ms. */
#else
SDK_DelayAtLeastUs(5000U, SDK_DEVICE_MAXIMUM_CPU_CLOCK_FREQUENCY);
#endif
#if BOARD_USE_FLEXIO_SMARTDMA
#if BOARD_LCD_S035
status = ST7796S_Init(&lcdHandle, &st7796sConfig, &g_dbiFlexioSmartdmaXferOps, &g_dbiFlexioXferHandle);
#elif BOARD_LCD_JLT35
status = ILI9488_Init(&lcdHandle, &ili9488Config, &g_dbiFlexioSmartdmaXferOps, &g_dbiFlexioXferHandle);
#else
status = SSD1963_Init(&lcdHandle, &ssd1963Config, &g_dbiFlexioSmartdmaXferOps, &g_dbiFlexioXferHandle,
BOARD_SSD1963_XTAL_FREQ);
#endif
#else
#if BOARD_LCD_S035
status = ST7796S_Init(&lcdHandle, &st7796sConfig, &g_dbiFlexioEdmaXferOps, &g_dbiFlexioXferHandle);
#elif BOARD_LCD_JLT35
status = ST7796S_Init(&lcdHandle, &st7796sConfig, &g_dbiFlexioEdmaXferOps, &g_dbiFlexioXferHandle);
#else
status = SSD1963_Init(&lcdHandle, &ssd1963Config, &g_dbiFlexioEdmaXferOps, &g_dbiFlexioXferHandle,
BOARD_SSD1963_XTAL_FREQ);
#endif
#endif
if (status == kStatus_Success)
{
#if BOARD_LCD_S035
ST7796S_SetMemoryDoneCallback(&lcdHandle, DEMO_DbiMemoryDoneCallback, NULL);
#elif BOARD_LCD_JLT35
ILI9488_SetMemoryDoneCallback(&lcdHandle, DEMO_DbiMemoryDoneCallback, NULL);
#else
SSD1963_SetMemoryDoneCallback(&lcdHandle, DEMO_DbiMemoryDoneCallback, NULL);
#endif
/* Clear the SSD1963 video ram. */
DEMO_ClearLcd();
#if BOARD_LCD_S035
ST7796S_EnableDisplay(&lcdHandle, true);
#elif BOARD_LCD_JLT35
ILI9488_EnableDisplay(&lcdHandle, true);
#else
SSD1963_StartDisplay(&lcdHandle);
SSD1963_SetBackLight(&lcdHandle, 128);
#endif
}
else
{
PRINTF("LCD controller initialization failed.\r\n");
}
return status;
}
static void DEMO_InitLcdClock(void)
{
}
static void DEMO_InitLcd(void)
{
#if defined(SDK_OS_FREE_RTOS)
s_memWriteDone = xSemaphoreCreateBinary();
if (NULL == s_memWriteDone)
{
PRINTF("Frame semaphore create failed\r\n");
assert(0);
}
#else
s_memWriteDone = false;
#endif
DEMO_InitLcdClock();
DEMO_InitLcdController();
}
/* Flush the content of the internal buffer the specific area on the display
* You can use DMA or any hardware acceleration to do this operation in the background but
* 'lv_flush_ready()' has to be called when finished
* This function is required only when LV_VDB_SIZE != 0 in lv_conf.h*/
static void DEMO_FlushDisplay(lv_disp_drv_t *disp_drv, const lv_area_t *area, lv_color_t *color_p)
{
lv_coord_t x1 = area->x1;
lv_coord_t y1 = area->y1;
lv_coord_t x2 = area->x2;
lv_coord_t y2 = area->y2;
int32_t length = (x2 - x1 + 1) * (y2 - y1 + 1) * LCD_FB_BYTE_PER_PIXEL;
#if BOARD_LCD_S035
ST7796S_SelectArea(&lcdHandle, x1, y1, x2, y2);
#elif BOARD_LCD_JLT35
ILI9488_SelectArea(&lcdHandle, x1, y1, x2, y2);
#else
SSD1963_SelectArea(&lcdHandle, x1, y1, x2, y2);
#endif
#if !defined(SDK_OS_FREE_RTOS)
s_memWriteDone = false;
#endif
#if BOARD_LCD_S035
ST7796S_WritePixels(&lcdHandle, (uint16_t *)color_p, length / LCD_FB_BYTE_PER_PIXEL);
#elif BOARD_LCD_JLT35
ILI9488_WritePixels(&lcdHandle, (uint16_t *)color_p, length / LCD_FB_BYTE_PER_PIXEL);
#else
SSD1963_WriteMemory(&lcdHandle, (const uint8_t *)color_p, length);
#endif
#if defined(SDK_OS_FREE_RTOS)
if (xSemaphoreTake(s_memWriteDone, portMAX_DELAY) != pdTRUE)
{
PRINTF("Wait semaphore error: s_memWriteDone\r\n");
assert(0);
}
#else
while (!s_memWriteDone)
{
}
#endif
/* IMPORTANT!!!
* Inform the graphics library that you are ready with the flushing*/
lv_disp_flush_ready(disp_drv);
}
void lv_port_pre_init(void)
{
}
void lv_port_disp_init(void)
{
static lv_disp_draw_buf_t disp_buf;
memset(s_frameBuffer, 0, sizeof(s_frameBuffer));
lv_disp_draw_buf_init(&disp_buf, (void *)s_frameBuffer[0], (void *)s_frameBuffer[1], LCD_VIRTUAL_BUF_SIZE);
/*-------------------------
* Initialize your display
* -----------------------*/
DEMO_InitLcd();
/*-----------------------------------
* Register the display in LittlevGL
*----------------------------------*/
static lv_disp_drv_t disp_drv; /*Descriptor of a display driver*/
lv_disp_drv_init(&disp_drv); /*Basic initialization*/
/*Set up the functions to access to your display*/
/*Set the resolution of the display*/
disp_drv.hor_res = LCD_WIDTH;
disp_drv.ver_res = LCD_HEIGHT;
/*Used to copy the buffer's content to the display*/
disp_drv.flush_cb = DEMO_FlushDisplay;
/*Set a display buffer*/
disp_drv.draw_buf = &disp_buf;
/*Finally register the driver*/
lv_disp_drv_register(&disp_drv);
}
void lv_port_indev_init(void)
{
static lv_indev_drv_t indev_drv;
/*------------------
* Touchpad
* -----------------*/
/*Initialize your touchpad */
DEMO_InitTouch();
/*Register a touchpad input device*/
lv_indev_drv_init(&indev_drv);
indev_drv.type = LV_INDEV_TYPE_POINTER;
indev_drv.read_cb = DEMO_ReadTouch;
lv_indev_drv_register(&indev_drv);
}
/*Initialize your touchpad*/
static void DEMO_InitTouch(void)
{
#if BOARD_LCD_S035
DEMO_LCD_I2C_Init();
gt911_config_t touchConfig = {.I2C_SendFunc = DEMO_LCD_I2C_Send,
.I2C_ReceiveFunc = DEMO_LCD_I2C_Receive,
.timeDelayMsFunc = DEMO_TouchDelayMs,
.intPinFunc = DEMO_TouchConfigIntPin,
.pullResetPinFunc = DEMO_TouchConfigResetPin,
.touchPointNum = 5,
.i2cAddrMode = kGT911_I2cAddrMode0,
.intTrigMode = kGT911_IntFallingEdge};
GT911_Init(&touchHandle, &touchConfig);
#elif BOARD_LCD_JLT35
DEMO_LCD_I2C_Init();
gt911_config_t touchConfig = {.I2C_SendFunc = DEMO_LCD_I2C_Send,
.I2C_ReceiveFunc = DEMO_LCD_I2C_Receive,
.timeDelayMsFunc = DEMO_TouchDelayMs,
.intPinFunc = DEMO_TouchConfigIntPin,
.pullResetPinFunc = DEMO_TouchConfigResetPin,
.touchPointNum = 5,
.i2cAddrMode = kGT911_I2cAddrMode0,
.intTrigMode = kGT911_IntFallingEdge};
GT911_Init(&touchHandle, &touchConfig);
#else
lpi2c_master_config_t masterConfig;
/*
* masterConfig.enableMaster = true;
* masterConfig.baudRate_Bps = 100000U;
* masterConfig.enableTimeout = false;
*/
LPI2C_MasterGetDefaultConfig(&masterConfig);
/* Change the default baudrate configuration */
masterConfig.baudRate_Hz = BOARD_TOUCH_I2C_BAUDRATE;
/* Initialize the I2C master peripheral */
LPI2C_MasterInit(BOARD_TOUCH_I2C, &masterConfig, BOARD_TOUCH_I2C_CLOCK_FREQ);
/* Initialize the touch handle. */
FT5406_RT_Init(&touchHandle, BOARD_TOUCH_I2C);
#endif
}
/* Will be called by the library to read the touchpad */
static void DEMO_ReadTouch(lv_indev_drv_t *drv, lv_indev_data_t *data)
{
#if BOARD_LCD_S035
touch_point_t tp[5];
uint8_t tp_count = 5;
GT911_GetMultiTouch(&touchHandle, &tp_count, tp);
/**
* GT911 supports 5 points tracking, we only tracks ID #0.
*
*/
bool found_track = false;
for (uint8_t i = 0; i < tp_count; i++)
{
/* Found track ID #0 */
if (tp[i].touchID == 0)
{
data->state = LV_INDEV_STATE_PRESSED;
switch (lcdHandle.orientationMode)
{
case kST7796S_Orientation0:
data->point.x = (int16_t)tp[i].x;
data->point.y = (int16_t)tp[i].y;
break;
case kST7796S_Orientation90:
data->point.x = (int16_t)(touchHandle.resolutionY - tp[i].y);
data->point.y = (int16_t)tp[i].x;
break;
case kST7796S_Orientation180:
data->point.x = (int16_t)(touchHandle.resolutionX - tp[i].x);
data->point.y = (int16_t)(touchHandle.resolutionY - tp[i].y);
break;
case kST7796S_Orientation270:
data->point.x = (int16_t)tp[i].y;
data->point.y = (int16_t)(touchHandle.resolutionX - tp[i].x);
break;
default:
break;
}
found_track = true;
break;
}
}
/* No track #0 found... */
if (!found_track)
{
data->state = LV_INDEV_STATE_RELEASED;
}
#elif BOARD_LCD_JLT35
touch_point_t tp[5];
uint8_t tp_count = 5;
GT911_GetMultiTouch(&touchHandle, &tp_count, tp);
/**
* GT911 supports 5 points tracking, we only tracks ID #0.
*
*/
bool found_track = false;
for (uint8_t i = 0; i < tp_count; i++)
{
/* Found track ID #0 */
if (tp[i].touchID == 0)
{
data->state = LV_INDEV_STATE_PRESSED;
switch (lcdHandle.orientationMode)
{
case kILI9488_Orientation0:
data->point.x = (int16_t)tp[i].x;
data->point.y = (int16_t)tp[i].y;
break;
case kILI9488_Orientation90:
data->point.x = (int16_t)(touchHandle.resolutionY - tp[i].y);
data->point.y = (int16_t)tp[i].x;
break;
case kILI9488_Orientation180:
data->point.x = (int16_t)(touchHandle.resolutionX - tp[i].x);
data->point.y = (int16_t)(touchHandle.resolutionY - tp[i].y);
break;
case kILI9488_Orientation270:
data->point.x = (int16_t)tp[i].y;
data->point.y = (int16_t)(touchHandle.resolutionX - tp[i].x);
break;
default:
break;
}
found_track = true;
break;
}
}
/* No track #0 found... */
if (!found_track)
{
data->state = LV_INDEV_STATE_RELEASED;
}
#else
touch_event_t touch_event;
static int touch_x = 0;
static int touch_y = 0;
data->state = LV_INDEV_STATE_REL;
if (kStatus_Success == FT5406_RT_GetSingleTouch(&touchHandle, &touch_event, &touch_x, &touch_y))
{
if ((touch_event == kTouch_Down) || (touch_event == kTouch_Contact))
{
data->state = LV_INDEV_STATE_PR;
}
}
/*Set the last pressed coordinates*/
data->point.y = touch_y;
data->point.x = touch_x;
#endif
}

复制代码

三、运行结果

下载程序后，显示屏运行LVGL例程

阅读全文

[原创] DIY-LCD显示模块--JLT35002A

浏览过的版块

站长推荐 /3